Kada iskljucim SMART za HDD u Bios-u, da li on i dalje negde belezi te varijable - ali je samo onemoguceno
njihovo citanje iz OS-a, ili ih i ne belezi, nego krece da "broji" samo od trenutka kada ukljucis SMART u Bios-u?
Ovo me zanima jer sam cim sam kupio komp iskljucio SMART u Bios-u, i sada me zanima ako ga sada
ukljucim hoce li mi dati podatke samo od kada sam ga ukljucio ili i od ranije?
(nadam se da razumete piranje, malo sam spetljao) :)
Sada mi je izlaz komande ovakav, ali to je valjda jer je disejblovan smart u bios-u:
Code:
srdjan@Zverko:~$ sudo smartctl -a /dev/sda
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD2500AAKS-00VYA0
Serial Number: WD-WCARY0097324
Firmware Version: 12.01B02
User Capacity: 250,059,350,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Jul 18 13:12:38 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x00) Offline data collection not supported.
SMART capabilities: (0x0000) Automatic saving of SMART data is not implemented.
Error logging capability: (0x00) Error logging supported.
General Purpose Logging supported.
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision number = 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
srdjan@Zverko:~$
..a ovo je sad, kada sam ukljucio SMART u Biosu (do sad mi je stalno bio iskljucen, od kada sam kupio komp, pre vise meseci):
Code:
srdjan@Zverko:~$ sudo smartctl -a /dev/sda
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD2500AAKS-00VYA0
Serial Number: WD-WCARY0097324
Firmware Version: 12.01B02
User Capacity: 250,059,350,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Jul 18 13:21:35 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (6480) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 78) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 157 154 021 Pre-fail Always - 5125
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 234
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 200 200 051 Old_age Always - 0
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 4259
10 Spin_Retry_Count 0x0012 100 100 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 195
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 51
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 234
194 Temperature_Celsius 0x0022 110 100 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 051 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
srdjan@Zverko:~$
- i sta mu znaci ono "Pre-Fail" (pred-crkavanje :) ) - i ono "Old-Age" - mislim znam da prevedem samo bukvalno, ali mi se bukvalan prevod ni malo ne dopada :))
[Ovu poruku je menjao Kernel-1 dana 18.07.2008. u 13:25 GMT+1]